Microtouch Titanium Head Shaver

The all new MicroTouch Titanium Head Shaver has Five rotary heads, forged from stainless steel, and bonded with titanium contour independently over the natural curvature of your head. MicroTouch Titanium Head Shaver gives you five times the coverage, and a closer, more comfortable shave with no nicks, cuts, or bumps. With an easy-grip, design, for perfect control, and rechargeable, lithium-ion power, to shave anywhere, any time. The ultimate wet/dry shaver with no creams, lotions, or soap needed. Features & Benefits: Conforms to every surface and curve
5x the coverage area of a razor.
Easy-grip, design, for perfect control.
 Rechargeable, lithium-ion power.
 Hypo-allergenic for sensitive skin.
Safe to the touch.
No nicks, cuts, or bumps.

See the full list of product ingredients on the product label.

Getting Started: Fully charge your Microtouch Titanium Head Shaver (see CHARGING) before first use.Use this shaver dry, with shaving gel, or shaving cream.If you are new to using the Head Shaver, we recommend you allow your skin and hair approximately 2 to 3 weeks to adapt.The Micro Touch Titanium® Head Shaver is not intended to shave more than 3-days stubble or hair longer than 1116th of an inch (1.5mm) in length. If your hair is longer than 1116th of an inch, trim your hair down with a hair clipper prior to using the Head Shaver.Shaving: Remove the protective cover then press the ON/OFF button located on the top of the Head Shaver.Place the Head Shaver in the palm of your hand, then gently press the Head Shaver against your skin.Glide the Head Shaver over your head using small, circular motions. Do not press too hard or you may damage the cutting heads and potentially cause skin irritation. When finished, power the Head Shaver OFF and replace the protective cap.Be sure to clean your Micro Touch Titanium® Head Shaver after every use (see CLEANING INSTRUCTIONS). Cleaning is especially important when using shaving creams or gel as they will dry and clog the cutting blades, resulting in poor cutting performance.Charging: Fully charge your Micro Touch Titanium® Head Shaver before its first use.When your Head Shaver battery is running low, the power indicator LED will begin to flash. This indicates you have approximately 10-minutes of shaving time left before you need to recharge the battery.To charge your Micro Touch Titanium® Head shaverTurn the unit off.Insert the charging cable into the USB-C port located on the side of the shaver.Insert the USB end of the charging cable into wall adapter or other power supply.During charging, the power indicator on the top of the unit will flash, when charging is complete, the power indicator will turn OFF.A full charge takes approximately 3-hours.Unplug Head Shaver when charging is complete. You can use the Head Shaver while it is charging. However, DO NOT use the Head Shaver in the shower or wet environment while plugged in and charging.
Cleaning: In order to achieve optimum cutting performance, from your Micro Touch Titanium® Head Shaver, it is important to clean the cutting head assembly after every use, especially after shaving with cream or gel.
Over a sink or garbage can, hold the Head Shaver in the palm of one hand. With the other hand, grip the sides of the cutting head assembly, between the cutting heads, and gently pull until the cutting head assembly separates from the body.
Tap the cutting head assembly and body to dislodge hair clippings. Use the small cleaning brush provided to sweep out any remaining hair from the head.Rinse the cutting head assembly under warm running water.Set both parts aside to air dry.
Reattach the cutting head assembly to the body when dry.Travel Lock: Prevents shaver from accidentally turning on when traveling.To LOCK: Press and Hold the ON/OFF button for 3 seconds.
The power indicator LED will flash 5 times when locking is complete.If ON/OFF button is pressed while locked, the power indicator LED will flash 3 times, but shaver will not turn on.
To UNLOCK: Press and Hold ON/OFF button for 3 seconds. Shaver will turn on after 3 seconds.

This appliance is not intended for use by persons (Including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Use this product only for its intended household use as described in this manual. Do not use attachments not specified by the manufacturer. Charge only with the charging cable provided with this product. Use only with a USB power adapter from a certified product, such as on a computer, receptacle lamp, Class 2 power supply or automotive adaptor. Never charge this product when it has a damaged cord or plug, when it is not working properly, after it has been dropped or damaged, or after it has been drooped in water. Always check the cutting head before use. Do not use this product with a damagedor broken cutting head, as it has the potential to result in injury. Kepp porduct, charing cord and USB power adapter away from heated surfaces. Always attach plug to product first, then to outlet. To disconnect, turn all controls to off postion, then remove plug from outlet. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. Never drop or insert any object into any opening. Do not reach for the product if it has fallen into water while charging. Unplug immediately for mthe receptacle. The power cord and the accessories connected to it are not for immersion of for use in the shower. Do not use whil bathing of in the shower. Except when charging, always unplug product from electrical outlet after charging. Do not place or store product where it is able to fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid. Unplug this product before cleaning.